Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In

Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
part number: C84VV

An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity.

Features:

• Brake controller activates trailer brakes with preset intensity
• Adjustable power output control lets you select the amount of braking force
  • Rocker switches located on left front of module for easy access
• 10 Gain settings and 9 load settings allow you to adapt to various driving conditions
  • Select a higher setting for harder braking and lower for more gradual braking
• Pinch-trigger manual override is within easy reach for controlling trailer sway or stopping in emergencies
• Simple LED display shows the amount of power output
  • Self-diagnostics monitor trailer connection and check for shorts
• LCD display shows power adjustments in 0.5 increments
  • Brightness is adjustable for optimal visibility
• Auto-sleep mode prevents battery drain after 5 minutes of idle time
• Quick and easy installation with no mounting restrictions
  • No need to mount level - install anywhere at any angle
  • Included mounting bracket and hardware designed to hold the brake controller flush against the dash
  • Plug-in, vehicle-specific brake control adapter (sold separately) available for select vehicles to reduce installation time

Specs:

• Application: trailers with up to 4 axles (8 brake assemblies)
  • Compatible with low-volt, PWM, ABS, cruise control, and electric-over-hydraulic trailer brakes
• Dimensions: 4" long x 3-1/8" wide x 1" tall
• Limited lifetime warranty

Gain Adjustment

Gain control lets you set the maximum amount of power that will be applied to your trailer's brakes, adjusting in increments of 0.5. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to go as high as you can without the trailer brakes locking up. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes. To get more power to your brakes, press the upper orange rocker switch. To decrease the gain, press the lower switch. When you make your adjustment, the gain setting will show on the LED screen for 10 seconds as a series of bars and then go into sleep mode.

Load Control

Once you have the gain set, you can fine-tune your braking by adjusting the load control on a scale of 1 to 9. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. Load control can get the braking power to your trailer faster and with more intensity so that it doesn't push your tow vehicle forward. If your vehicle takes too long to come to a stop, increase the setting by pressing the upper black rocker switch. If it stops too abruptly, decrease the setting by pressing the lower switch. You can alter the setting to suit your driving preferences or to improve handling based on changing road conditions or varied trailer loads.

Pinch-Trigger Manual Override

The Discovery comes with a easy-to-reach, pinch-trigger manual override, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push in the trigger. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.

LED Display

The LED display on the Discovery is large and easy to read at a glance. It will show you what setting the brake controller is on as well as give you information for troubleshooting. You can adjust the screen brightness or trigger night mode so it won't glare obnoxiously on your dash. Press the control button to cycle through the different modes.

Quick Installation

Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, so long as you can still easily access the controller and the manual override. The included bracket is designed to mount the brake controller flush to the dash so it takes up almost no space at all.

If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.

Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:

20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications

30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications

See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.

Time-Delayed Braking

The Curt Discovery comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the Discovery. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. Both the amount of braking power (gain) and rate of application (load) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.

51126 Curt Discovery NEXT Time Delay Trailer Brake Control - 1 to 4 Axles

Replaces Curt 51120

Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
part number: C51332

Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.

Features:

• Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
• No cutting or splicing required
  • Custom connector end plugs into the built-in port beneath the dash of your vehicle
  • Other end plugs into the back of your electric brake controller
• Compatible with time-delayed and proportional brake controllers from Curt
  • Brake controller must have built-in plug for adapter to connect - will not work on controllers with pigtail wiring harnesses
• 2' Long, 12-gauge wires have protective covering to deter damage
• Limited 1-year warranty

Installation of Curt Brake Controller Adapter

To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. When this is done, a port is installed at your dash so that you can easily plug in a brake controller.

This adapter plugs into the port on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, and it is taped to another harness near the emergency brake pedal.

No hardwiring is required to install this adapter. After you plug it into the factory port, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.

51332 Curt Quick Plug Brake Control Adaptor Harness

California residents: click here

WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov

Customer Satisfaction Score:

97% were satisfied with this product

3% of customers were not satisfied

• Defective
• Product did not meet expectations
• Alternate product found

Learn More

Customer Reviews

Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed - C84VV

Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In - C51332

Average Customer Rating:  4.7 out of 5 stars   (132 Customer Reviews)

Order: RelevanceNewestRating - High to LowRating - Low to High An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity. Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.

by: Thomas08/09/2023

It does not fit my vehicle. On the attached photo the connector on the left is the stock dodge plug, the plug on the right is what I just got1642382

Click to Enlarge

Brooke M.

8/23/2023

Hmm...youll be looking for another white plug like the white harness. Do you know if your truck for sure has the factory tow package?

by: Kory K03/18/2014

2008 DodgeRam Pickup

Sorry for the late follow-up. I just wanted to let you know that the brake
controller and wiring harness I purchased through eTrailer worked very well
with my 2008 Dodge Ram 2500 with the Cummins 6.7L diesel. Pictures are
attached for your use, as required.

The trailer was an 18-foot enclosed snow machine tailer with a steel
chassis. I can't remember the empty weight, but it's substantial. We towed
empty and full on dry and snow covered roads from Oklahoma to Colorado and
back. Even with th exhaust brake on my truck, I can't imagine towing this
load through the hills and mountains without a brake controller. It's been
done before, but I would say it's an unnecessary risk given the more than
reasonable prices at eTrailer...it was cheap insurance pulling such a heavy
rig with my family on board.

The controller was definitely not your top-of-the-line model, but the
adjustability and controls were more than adequate for somebody who tows
occasionally. A professional may desire more proportional controls and
adjustability, but not much more. This unit peformed flawlessly.

Thank you for your time. Please feel free to contct me if you would like
any clarification on my statements or pictures.121175

Click to Enlarge

Click to Enlarge

by: Robert J. 07/15/2018

2007 DodgeRam Pickup

This item easily plugged into my Curt brake controller and into my truck’s factory plug. Made for a less than 5 minute install; powering up the brake controller with no issues. Convenient is an understatement with this pigtail. Rig is 2007 Dodge Ram 2500 4X4 CTD. 542059

Click to Enlarge

by: Steve T.06/18/2016

1999 DodgeRam Pickup

Perfect fit for my 1999 Dodge Ram. it made installation of the brake controller super easy. I highly recommend paying the extra $** for this item.262433

Click to Enlarge

by: Tim 09/02/2022

The folks at etrailer are the best! Very helpful and knowledgeable!! The product I received fit perfectly and works great!!1389896

Tim

9/3/2023

Still working great!

by: Jim 02/09/2024

2004 DodgeRam Pickup

y0u want good go to etrailer was a perfect fit1725163

by: David H07/31/2017

I ordered a fifth wheel brackets and hitch along with curt brake controller and pigtail. Everything fit great with no problems and the service and shipping was very speedy. Highly recommend etrailer for all your needs. 414208

Click to Enlarge

by: Jerry 04/25/2024

Tested . Work fine and advertised 1772901

by: Micah07/18/2022

DodgeRam Pickup

2006 Dodge Ram. Easy install. Plug it in and tie up the wires. I put a wire protector sleeve to cover the wires coming out of the controller.1333098

Click to Enlarge

Click to Enlarge

Click to Enlarge

by: Ethan 03/15/2024

excellent service and delivery. 1748195

by: Jay L04/04/2014

Trailer control shipped quickly, super easy install with the pigtail. Happy customer!123777

Click to Enlarge

by: Jesse 12/18/2023

fit and finish was perfect. 1703620

by: Jeff M09/25/2017

DodgeRam Pickup

In hind sight I probably didn't need to order this item. Forgetting how difficult it was to access the connector on my Dodge Ram when I installed my first (now defunct) brake controller, I imagine it will be a greater struggle to get it to disconnect before putting the new one on. So I think what I'll do is cut the Dodge specific connector off the one end, cut the wires off my old controller and splice this pigtail into it, thus eliminating the need to remove the old connector!436199

Jeff M.

9/25/2018

My splice job worked as planned however I no longer own that vehicle.

by: Mike D07/16/2016

Dodge

I needed an electric brake control for my 2006 Dodge pickup but was having trouble finding one locally that would plug in to the factory installed plug. If it was a Chev or Ford it was in stock and I didn't want a universal that would have to cut into the wiring. I called etrailer to make sure what I saw on their website was correct and they assured me it was so I ordered it. It arrived, I instaled it and it works perfect.272433

Michael D.

7/16/2017

Still working fine.

by: Sidney 09/21/2023

Like its compact size and simple operat ion.1671425

by: Bill09/12/2022

DodgeRam Pickup

The directions on this item are horrible. I finally figured it out and was able to install it onto my Ram 1500, but only after spending hours trying to make everything fit right. If you're looking for a hitch setup to pull a trailer long distances, I would advise you to look at other options. This will work for my short trips with my half-ton pickup, but I would not want to pull anything more than 50 miles with this setup.1427858

by: Dusten09/21/2023

Very helpful, knowledgeable and friendl y!1673264

by: John 09/26/2023

Fast Shipping! Works great! Easy to ins tall!!1673540

by: Larry J Warren04/18/2014

Used in conjunction with the Curt brake controller I purchased from etrailer.
Worked perfectly.125925

Larry W.

4/18/2015

Works fine No reliability issues, worry free.

by: KEITH09/15/2020

I ordered the Curt TriFlex trailer brake controller. Had to return the first one, due to the manual brake activation lever being sloppy loose. They replaced it with no hassle. It looks cheap but works good so far894563

by: Robert A.04/21/2017

DodgeRam Pickup

My 07' Dodge Ram Quad Cab had a factory installed receiver hitch and therefore the plug to which this cable attached. However, I had to go to the Curt mfg website to find a picture of the actual truck plug. Once I found the plug which was buried up in a difficult spot to reach, the cable snapped in easily. It is sufficiently long enough to reach the controller cable if one installs the controller anywhere on the knee panel below the steering wheel.

370430

by: Ralph06/27/2023

Worked great performance as described 1609955

by: H. Miller11/28/2013

Land Rover Discovery II

I ordered a Curt Discovery trailer brake controller. Exactly what I was looking for and for a great price. Transaction was smooth and easy and the controller arrived within a reasonable amount of time. I liked the parcel tracking that showed the progress of my order.108699

by: David C05/17/2014

I used this connector with a new brake controller that I also purchased. It was very easy to connect to the controller & truck's electrical system (under the driver's side dash). So far it's working beautifully.

As always, etrailer was excellent with their advice, shipping, and follow-up emails. I have had great experiences with them since 2010.131086

by: David10/11/2013

2008 DodgeRam Pickup

The Curt wiring adapter made installation of the Curt Triflex brake controller on our 2008 Dodge Ram 3500 a breeze. Just plug one end into the brake controller plug and the other into the pre-existing plug-in all ready under the dash, then added a couple zip ties to keep it up and out of the way. It couldn't have been any easier. The plug in connection also allows the brake controller to be moved easily from truck to truck if needed103427

25

132

Show More Reviews

Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?

• Does Dealer Need to Turn on Aftermarket Brake Controller in a 2015 Ford F-150?
  
• There will be no need for you to go to take your 2015 Ford F-150 to the dealer to have them turn on an aftermarket brake controller. The brake controller I recommend that you need only an adapter for is the Curt Discovery # C84VV. Since you already have the factory tow package, just use the Plug-In Wiring Adapter # C51436. Plug one side into the brake controller and the other side into the wiring on your F-150 and you are done.
  view full answer...


• Brake Controller Installation on 2011 Toyota Tundra
  
• If your 2011 Tundra has the factory tow package, which includes the factory installed 7-way trailer connector on the rear bumper, it will be equipped with the tow package plug under the dash, as shown in the photo I've edited for you. Some models with the factory 4-pole (or 4-pin) trailer connector will also have the plug under the dash, you'll need to look for a white plug located above and to the left of the emergency brake pedal, above the toe kick. Occasionally, the plug will be located
  view full answer...


• Troubleshooting No Power on Blue Wire After Installing Curt Discovery Brake Controller
  
• The issue you're describing likely has to do with the red brake input wire coming from the Curt Discovery Brake Controller # C84VV and corresponding harness # C51515. You will want to make sure that this red wire is connected to the cold side of the brake light switch behind the Suburban's brake pedal. This is the wire that ONLY gets power when the brake pedal is depressed and no power with any other function. I recommend using a circuit tester like # PTW2993 to verify you have found
  view full answer...


• Why Is Stoplight Circuit Difficult to Find on 2017 Ram 1500 For Installing Brake Controller
  
• Your generation of Ram truck uses a powernet style of wiring at the brake switch wiring which means the voltage will actually read lower than what a 12 volt circuit tester is going to show. Also if you are trying to hardwire a controller you are going to have issues as we've found that if you don't use a harness designed specifically for your truck's wiring setup you may damage the vehicle. So to install the Curt Discovery part # C84VV you have to use the vehicle specific install harness
  view full answer...


• Brake Output on Connector with No Trailer Connected Using Curt Discovery Trailer Brake Controller
  
• In regards to the Curt Discovery Trailer Brake Controller part # C84VV, there should not be power on the brake output pin inside the trailer connector without a trailer hooked up. There could be a few different things causing this but in order to rule out the brake controller you'll want to do a bench test outlined below. If the controller test good then that means you have a short on the brake output wire on the vehicle and you'd need to start tracing and checking for shorts. It may also
  view full answer...


• Curt Brake Controller Wiring Harness for 2018 Ford F-150
  
• Curt replaced the 51437 with the # C51436 which fits a 2018 Ford F-150 (among other Ford vehicles) and is compatible with the # C84VV Curt Discovery brake controller.
  view full answer...


• Curt Brake Controller Wiring Pigtail for 2013 Jeep Wrangler Unlimited
  
• The correct pigtail wiring harness for installing a Curt Discovery Trailer Brake Controller # C84VV in your 2013 Jeep Wrangler Unlimited is part # C51515.
  view full answer...


• How Does Brake Controller Install in 2012 Ford F-150
  
• When installing the Curt Discover part # C84VV with the harness for your 2012 Ford F-150, part # C51436 all you'd have to do is plug in the controller and harness and you'd be set if you have the factory 7-way like it sounds like you do. It's really a pretty simple install. Otherwise you'd need a 4-way to 7-way adapter like part # 37185 and you'd have to run the wire from the truck's frame rail to the adapter and you'd be set. See attached picture for more info on that.
  view full answer...


• Comparing Curt TriFlex Trailer Brake Controller To Curt Discovery Trailer Brake Controller.
  
• The main difference is the Curt TriFlex Trailer Brake Controller # C24VV is a proportional brake controller while the Curt Discovery Trailer Brake Controller # C84VV is a time delay controller. The proportional controller will automatically adjust power sent to your trailer brakes based on how hard you are braking, while the time delay always sends the same force no matter how soft or hard you are braking. Those with time delay controllers will often have to reach down to crank up the
  view full answer...


• Curt Discovery Brake Controller Display Flashes with Left Turn Signal
  
• It could be a wiring issue. Specifically, it is likely related to the brake controller red wire. If that wire is not attached to the correct circuit, it can cause some strange things to happen. The red wire needs to be connected to a brake switch wire that only has power when the brake pedal is pressed. If that same wire has power, then the headlights or a turn signal are on then it is not the correct wire. I have heard that the correct brake switch wire is the white wire so use a circuit
  view full answer...


• Curt Discovery Trailer Brake Controller # C84VV Displays Only a Red Dot After Installation
  
• If your Curt Discovery Trailer Brake Controller # C84VV displays only a red dot when you do NOT have a trailer connected then this indicates that the controller's red (input signal) wire is connected to the wrong side of the brake light switch. This red wire should connect to the COLD side of the switch that has power only when you press the brake pedal. If your Discovery displays the red dot when you DO have a trailer connected then this usually indicates a problem in the trailer brake
  view full answer...


• Help! Curt Discovery Trailer Brake Controller # C84VV Only Shows Decimal When Brake is Applied
  
• Since the Curt Discovery Trailer Brake Controller, # C84VV, is still displaying the decimal when the trailer is connected, the controller is not sensing a connection with the trailer brakes. In this case the issue is most likely related to a wiring problem or brake magnet problem. I would start by making sure that there isn't any corrosion in either connector. Next, I recommend using a circuit tester like part # PTW2993, to make sure that you have power on the brake controller output pin
  view full answer...


• How to Wire in a Curt Trailer Brake Controller to a 1999 Ford F-150
  
• Actually you have a couple of options. First, you could use harness # C51322 in place of the harness for your 1999 Ford F-150. It will plug into the Curt brake controller and the truck. This is the easiest option. The other option is to cut off the plug on the Curt brake controller # C84VV and hardwire it to the Ford harness. You would have to know the functions of the wires on the Ford harness. It may be labeled or printed on the harness. If your Ford harness has Red, Light Green,
  view full answer...


• How to Find and Access the Brake Light Switch Wire on a 2015 Toyota Highlander for Brake Controller
  
• If you check out the video I attached you will see how we installed a brake controller in a very similar 2014 Toyota Highlander as your 2015 model. We had to remove the lower dash panel (13:00 mark of the video), to make accessing the green wire possible. The kit used for the install in the video is the part # ETBC7.
  view full answer...


• Brake Controller Wiring Harness for Curt Discovery in 2017 Chevrolet Colorado
  
• Brake controllers are not vehicle specific technically the Curt Discovery # C84VV will work in your 2017 Chevrolet Colorado. The # C51515 wiring harness is the correct one for the Discovery.
  view full answer...


• Troubleshooting Curt Discovery Trailer Brake Controller # C84VV Installed in 2002 Chevrolet Tahoe
  
• Thank you for your recent purchases from etrailer. I would like to suggest some additional testing before you return the Curt Discovery Trailer Brake Controller # C84VV. This will help isolate the problem and confirm whether the unit is indeed defective. The code OL indicates that the controller has sensed an overload condition. Disconnect the trailer from the Tahoe. Apply your grounded tester to the pins at the 5-o-clock and 7-o-clock positions on the Tahoe 7-way, as shown on the
  view full answer...


• Troubleshooting Aggressive Trailer Braking with Curt Discovery on a 2018 Chevy Silverado 1500
  
• Have you tried going different speeds when you are adjusting the power output of the Curt Discovery Trailer Brake Controller # C84VV on your 2018 Chevy Silverado 1500? If you are only testing it at a slow speed and the brakes on your trailer are already set to be aggressive then it wouldn't take very much for your trailer to brake. Try putting the power output at the lowest setting for the Discovery, test it, and then go to the highest setting and see if that makes a difference. Let
  view full answer...


• Troubleshooting Trailer Brakes that Lock Up When Trailer Is Connected
  
• There is a short or a mis-wire on the 7-way you installed. It sounds like the 12 volt accessory circuit is shorting out to the brake output circuit which is causing the brakes of the trailer to lock up anytime the 7-way is connected. This is a fairly common issue as wiring up connectors is a bit confusing. Since the controller never senses a connection it sounds like the problem is the circuits just being wired backwards. I attached a chart that has what the 7-way pin out should look like.
  view full answer...


• Issues with Brakes Not Activating with Curt Discovery Brake Controller on 2015 Ram 1500
  
• I spoke with my contact at Curt about the issues you and other customers have experienced with their Curt Discovery Brake Controllers # C84VV and newer model Ram trucks. The problem stems from a low voltage output on the stoplight wire on the truck. The Discovery requires 12 volts from the stop light wire in order to recognize the signal and activate the trailer brakes. Curt has found that the newer Ram trucks often have less than 12 volts at the stop light wire when the brake pedal
  view full answer...


• Harness Needed To Install Curt Trailer Brake Controller On 2021 Nissan Frontier w/ Tow Package
  
• In order to install the Curt Discovery part # C84VV on a 2021 Nissan Frontier with factory tow package you'll simply need the Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51382.
  view full answer...


• Where is Brake Controller Adapter Plug Located In 2002 Dodge Ram Pickup
  
• The green connector in your truck is not the correct plug. It is normally a blue plug like what I have shown in the photo that plugs into the adapter part # C51332 if you are using a Curt brake controller like part # C51170. There will be a port to plug into if the truck came with a factory 7-way plug just to the right of the emergency brake. If the 7-way plug was installed after-market, you will need to see how far the wires from the plug are extended so you can complete the install
  view full answer...


• Quality Trailer Brake Control for a 2006 Dodge Durango
  
• You are thinking of Tekonsha brake controllers. They are pretty much the leader in the brake controller industry. The Curt controllers would not be my first choice. I prefer Tekonsha controllers because they have a long proven track record of quality and performance. The Curt controllers are a less expensive option but they are new to the brake controller industry. They did have some performance issues initially but they are improving. I recommend the Tekonsha P2, # 90885. This is a
  view full answer...


• Curt Spectrum Brake Controller Showing no Trailer on 2000 Dodge Ram 2500 After Replacing Connectors
  
• Yes, you are definitely on the right track. If your Curt Spectrum Trailer Brake Controller # C51170 is still not showing a trailer is connected and you have already replaced the connectors, I think it has to be a short either on the brake wiring or the brake magnets themselves. Before replacing your brake assemblies entirely, start by just checking the wires to the brake magnets (if you have not done so yet) and look for wires that may be pinched or otherwise damaged and fix as necessary.
  view full answer...


• Curt Brake Controller Recommendation for 2005 Dodge Ram 2500
  
• The price for the Venturer controller part # C74VV and install harness part # C51332 is tough to beat but a proportional brake controller will be a much better option. Proportional controllers sense how hard you are applying the brakes and apply the trailer brakes the same way. Time-delayed like the Venturer put out a preset amount of braking power so they aren't as effective. So instead the Triflex part # C24VV with the install harness # C51332 would be the better option for your 2005
  view full answer...


• Installation of Brake Controller on 1997 Ram 1500 Club Cab with Factory Trailer Plug
  
• We do appreciate your continued patronage and I think we can assist you with this. If you can't find the plug and the dealer doesn't offer any help on this, then you can hard wire in the controller to your 1997 Ram 1500, so you will be able to install the controller it'll just be a bit more time consuming. You will need a circuit tester like the # PTW2993 to test wiring functions under the dash, and you may need some butt connectors like the # DW05745-5 to complete your wiring connections.
  view full answer...