CargoGlide 1500XL Sliding Tray for Trucks - Heavy Duty - 1,500 lbs - Steel Frame - 8" Rail

2016 Chevrolet Silverado 3500 - CargoGlide 1500XL Sliding Tray for Trucks - Heavy Duty - 1,500 lbs - Steel Frame - 8" Rail

Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - 100 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 1,500 Lbs capacity.

Features:

• Sliding tray extends out 100 percent of its length from your truck bed for convenient access to cargo
• Built-in safety stops lock tray in place at 12" increments along glides
  • Prevent accidental extension of tray
  • Allow manual bypass with release latch
• 36 Bearings provide strong cargo support and smooth tray glide, even when you're parked on uneven surfaces
• Laminated, 3/4", marine-grade plywood deck supports cargo and prevents skid
  • Textured polypropylene surface resists tears, chemicals, moisture, and flame spread
• Adjustable feet let you fine-tune the tray height for tailgate clearance
• Handle cutouts with deck-over-latch release lever enable easy extension of tray
  • Increases tray surface area while providing safe position for fingers and hands
• 4" Tall extruded aluminum side and cab-end walls help contain cargo
  • Increase to 8" tall near the cab end of the tray
• Integrated tie-down tracks on side and cab-end tray inside walls help you secure cargo
  • Include 4 marine-grade eyebolts
• Black powder-coated steel tray frame is durable and rust resistant
• Pre-assembled tray bolts securely to your vehicle's bed with included PlusNut hardware
  • Installs on your truck bed in a few simple steps
  • Requires drilling
• Made in the USA

Specs:

• Tray weight capacity: 1,500 lbs
• Number of bearings: 36 - with a combined load rating of 57,158 lbs
  • 4 Load bearings - 3,019 lbs each
  • 16 Load bearings - 2,508 lbs each
  • 2 Carrier bearings - 2,473 lbs each
  • 14 Side-thrust bearings - 1,573 lbs each
• Tie-down track weight capacity: 400 lbs per anchor point
• Tray dimensions:
  • Outside: 95" long x 41-1/4" wide
  • Inside: 94" long x 48" wide
• Warranty:
  • 4 Years on frame
  • 2 Years on bearings
  • 1 Year on deck surface and substrate

Please note: Because of the size of this item, it ships via truck freight.

The CargoGlide XL slide-out truck tray extends out 100 percent of its length so you can easily load and unload items in your truck bed without climbing, crawling, or excessive reaching. Instead, this custom-fit bed slide brings the cargo to you - whether you're hauling toolboxes, yard bags, paint cans, or even large appliances and construction materials. And it boasts a 1,500 lbs capacity. Simply move the release lever and give the tray a pull. The tray includes built-in tie-down tracks with eyebolts to help you strap down your cargo. The CargoGlide is perfect for do-it-yourselfers, contractors, hunters, and designated grocery-getters. It's made from top-grade materials, and it installs to your truck bed in just a few steps.

Custom-Fit Sliding Truck Bed Tray

The CargoGlide is custom-fit for your vehicle to make the best use of the available space in your truck bed.

The sliding tray works like a supersized, high-quality toolbox drawer. Pull the tray out to bring your gear to you without reaching or climbing up into the bed of your truck. The tray's 36 tough, high-quality bearings are designed to glide smoothly even when the tray is loaded to capacity, so it's a cinch to move heavy loads into and out of your truck bed.

The CargoGlide uses a combination of full complement, permanently-sealed bearings and sealed needle bearings to ensure smooth, dependable operation without binding, whether you're parked on a level surface or an uneven one, such as a hill or ditch.

Adjustable Positioning

The CargoGlide has a locking point every 12 inches. These built-in stops let you extend the tray in increments and they serve as safety stops. When fully extended, the tray pulls out to 100 percent of its length.

To slide the tray out, locate the 2 cutout grab handles and red paddle-latch release. Move the latch to release the tray, grab a handle, and pull. You can bypass the stops by maintaining pressure on the latch. To close the CargoGlide, simply push the tray back in until it locks into place.

Sturdy, Slip-Resistant Tray with Tie-Down Track System

The CargoGlide's tray is a stout, 3/4" thick sheet of moisture-resistant, marine-grade plywood, laminated with TPO - a tough, polypropylene-based material that resists water, chemicals, abrasions, and flame spread. The tray is held in place by a sturdy steel frame, finished with a chip-resistant powder coat, and it will remain rock steady as you load or unload tools and equipment. The sturdy construction means it won't bend, warp, or twist under a load. The tray can also be tilted up and removed from its track if you need to make room for tall loads.

The tray is surrounded on three sides by extruded, 6061-T6 aluminum walls, 4" tall, designed keep your cargo from sliding off the tray and from bumping into the sides of your truck. The CargoGlide also has a built-in tie-down system that helps control your cargo. A track runs along the side and rear inside walls of the tray to give you lots of options for securing your load. The tray comes with 4, marine-grade steel O-rings that can be positioned anywhere along the track to create tie-down points for your cargo. Each tie-down track anchor point has a 400-lbs capacity.

To help contain larger cargo, the walls have extensions built-in that add 4" of height for the first 4' of the tray, beginning at the cab end.

Hassle-free Installation

The CargoGlide can be installed in a few simple steps. It's designed to be attached at 4-6 points in your truck bed using PlusNuts and bolts - all part of the included hardware packet. You will need the following tools: tape measure, crescent wrench, drill, knife, 5/16" bit, 1/2" bit, 1/2" socket, and a ratchet or impact driver.

The steps are straightforward (consult manual for full instructions):

1. Position the CargoGlide in your truck bed and determine clearances (you will need another person to help lift)
2. Locate and mark attachment points. Make sure there are no gas lines or other obstructions under the truck or van bed where you plan to drill.
3. Drill the pilot holes installation holes.
4. Install PlusNuts, bolts, and washers. Then tighten bolts.

Easy Loading/Unloading for Bicycles

The CargoGlide can be equipped to offer convenient bicycle transport. Install fork- or frame-mount truck bed bike racks (sold separately), and then slide the tray out for bike loading/unloading. No more awkward lifting or painful jabs from pedals and handlebars as you hoist bikes into and out of your truck bed.

Adjustable Height

The 2 adjustable feet on the underside of the tray allow you to fine-tune the height of the CargoGlide tray when you install it. This allows you to customize the tray to the perfect height for clearing your tailgate. Turn the feet clockwise to shorten the height of the tray or rotate the feet counterclockwise to extend it up.

CG1500XL-9548 Cargo Glide XL Truck Bed Slide - 100 Percent Extension - Steel Frame - 1500 Pounds Capacity

Replaces CG1500-9548