Gas Struts Specs:
Features:
If your vehicle's hood keeps closing while you're trying to work on your engine, it's time to change your strut. Replace it with this custom fit gas strut and make your hood operate like new again. Quick, tool-free installation.
More Information >Gas Struts Specs:
Features:
If your vehicle's rear window keeps closing while you're unloading cargo, it's time to change your strut. Replace it with this custom fit gas strut and make your window operate like new again. Quick, tool-free installation.
Tech Tip:
Product is intended to fit Eddie Bauer models only.
More Information >Gas Struts Specs:
Features:
If your vehicle's liftgate keeps closing while you're unloading cargo, it's time to change your strut. Replace it with this custom fit gas strut and make your liftgate operate like new again. Quick, tool-free installation.
Tech Tip:
Product is not compatible with Eddie Bauer models.
More Information >Gas Struts Specs:
Features:
If your vehicle's hood keeps closing while you're trying to work on your engine, it's time to change your strut. Replace it with this custom fit gas strut and make your hood operate like new again. Quick, tool-free installation.
Installation Notes:
Designed to fit vehicles with steel hoods only
More Information >Videos
for Lift Supports
Help Articles
for Lift Supports
Expert Answers
for Lift Supports
Hey thanks for reaching out, Robert. Your Dexter P-15 model SLR 3,500 lb axle does use the standard bearing combination for a 3,500 lb axle. I was able to confirm this with Dexter. So, you have #L68149 for the inner bearing and #L44649 for the…
view full answer...I have included a video that briefly goes over installing the Hopkins EasyLift Truck Bed Tailgate Lift Assist #74211 but we do not have a video that goes over the entire installation process. As you can see in the video you will need to drill a…
view full answer...Hi Robert; the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100 is the correct bearing kit for your axle.
view full answer...Hey Jason, so we don't have the Hopkins tailgate assist part #74211 listed as a fit for your 2011 Ford F-350 but we do have the DeeZee part #DZ43203 as a fit.
view full answer...The Air Lift LoadLifter 5000 #AL88200 will work with the Air Lift Air Helper Spring Cradle #AL59DQ on your 2013 Ford F-150. The cradle actually replaces the lower roll plate so the air bag will sit directly in the cradle. I'm not sure…
view full answer...You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub…
view full answer...Hey Lucas, The Curt MV #C17050 is for total tongue weights between 500 lbs and 600 lbs only (600 lbs isn't actually the minimum), and for a 5,000 lb GVWR camper, the tongue weight is definitely going to exceed what this hitch is capable…
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…
view full answer...To flat tow a 2011 to 2013 Jeep Grand Cherokee there are 5 major components needed: base plates, tow bar, safety cables, lighting, and supplemental braking. The base plates are what attach to the front of the Jeep and provide a safe and proper…
view full answer...Thank you for all the info John, Based on the numbers you provided your pin box has a Rhino bolt pattern with a 21,000 capacity. To find the correct Gen-Y pin box we'll need to check your trailer's pin weight. If the pin…
view full answer...Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.
view full answer...Filter Products (4)