Explore Expert Info
on ATV UTV
on ATV UTV
Explore Expert Info
- Backing Plate for Use with Erickson ATV E-Track Tie-Down Kit EM09160
Erickson does offer a zinc-plated steel backing plate for use with their E-Track products like their ATV E-Track Tie-Down Kit #EM09160. Use part #BPEZ. You can see this item's hole dimensions and spacing in the linked photo. Since your trailer… view full answer...
- Replacement Winch for 2008 Arctic Cat 400 with Factory Mounting Plate
It looks like the Warn 2.5 ci was a 2500-lb capacity winch, so you can use the Bulldog #BDW15002 as a replacement for that winch and get a slight upgrade in capacity. This winch will mount to the mounting plate #BDW15108 which is designed for the 2… view full answer...
- Similar Toolbox To DeeZee DZM207 that is Not Diamond Plate
The closest tool box we have to the DeeZee #DZM207 that you referenced that does not have diamond plate would be the part #DZ8546SB which is a bit bigger at 46-1/2" Long x 19" wide x 15-9/10" tall and has 8 cubic feet of space. view full answer...
- How To Charge Trailer Battery On Dump Trailer Using The 7-Way Trailer Connector
You will want to use a circuit tester like part #40376, and check the #4 terminal on the back of the 7-way trailer connector on your trailer for power. This is the 12 volt power terminal so there should be power to that terminal. You will need to run… view full answer...
- Dimensions of Bulldog Winch Mount for 2016 Kawasaki Teryx
I reached out to a representative of Bulldog who said the Bulldog Winch Custom-Fit Steel ATV Winch Mount #BDW15176 measured approximately 9 inches wide, 7-1/2 inches deep and 3-3/4 inches high (to the bottom of the mounting plate). You can use these… view full answer...
- Recommended Custom Winch Mount for Honda 420 Rancher Winch
The Bulldog Winch Custom-Fit Steel ATV Winch Mount #BDW15114 is a custom fit for your Honda Rancher TRX420 for 2007-2014(with independent rear) models. I've attached a video to assist. Another option is the Bulldog Winch Custom-Fit Steel ATV… view full answer...
- Winch Mount Fit For a 1997 Suzuki King Quad 300
For your 1997 Suzuki King Quad 300 the Bulldog Winch ATV mount part #BDW15135 that you referenced is a confirmed fit. view full answer...
- How to Choose a Trailer Sway Control Solution
The anti-sway solution you need will depend on the weight, length and trailer you're towing. If you're towing a smaller flatbed utility type trailer that gets a little unstable from time to time, and moving more tongue weight to the front of… view full answer...
- Attaching E-Track to Wooden Trailer Floor
Ideally, you'll want some of the hardware attaching the e-track to the trailer floor to also secure to the cross members as well as to the planks that make up the trailer floor. If that's not possible, I'd recommend using a backer plate… view full answer...
- Does the Curt/Draw-Tite Trailer Hitch for a 2019 Honda Passport Install Behind the Bumper Panel
I have attached a photo of the Curt Trailer Hitch Receiver part #C13421 installed on a 2019 Honda Passport. As you can see, the receiver tube is tucked neatly under the rear bumper but it does not install behind the rear bumper panel nor do any of… view full answer...
- E Track Tie Down Kit Recommendation for Razor UTV
If your trailer has Etrack installed in it like the part #E19148 the Erickson ATV E-Track Tie-Down Kit #EM09160 that you referenced would be a great option. This kit has a safe working load limit of 1,500 lbs with a max break strength of 4,500 lbs so… view full answer...