Looking for 10 Inch Ball Mount With 3 Inch Rise and 1 Inch Trailer Ball Mounting Hole
Question:
I need a class III drawbar for a 2-inch square tube, 3-inch or 3-and-one-eighth-inch rise, with 10-inch length. Oh, and a 1-inch dia. ball hole. It is for a light tear trailer under 1,400 pounds loaded. The drawbar I have now has a three-quarter inch rise and it is too low for me to properly lower and raise my front wheel the one you crank up and down. Thanks
asked by: Jim W
Expert Reply:
The closest we can get to a 3 inch rise with an inexpensive ball mount in the length and with the trailer ball hole diameter you're wanting is the # 2753 which offers a 2-3/4 inch inch rise and a 9 inch length. The ball mount includes a hitch pin.
If that won't provide enough rise for your trailer jack, CR Brophy offers an aluminum ball mount, part
# EA40 that would offer a 3 inch rise, has a 10-1/2 inch length (center hitch pin hole to center ball mounting hole) and a 1 inch diameter hole where the trailer ball installs. This ball mount doesn't include a hitch pin, which is sold separately as part # PC3
Products Referenced in This Question
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Brophy Ball Mount - 3" Rise, 4" Drop - 14-5/8" Long - Aluminum - 8,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Aluminum Shank - Silver
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 8000 lbs GTW
- Class IV
- Long Shank
- Brophy
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Which Hitches are Made in the USA
- Q&A: Recommended 2-Inch Trailer Hitch For 2024 Mazda CX-5
- Q&A: Difference Between Curt & etrailer Trailer Hitches For 2024 Subaru Crosstrek Wilderness
- Q&A: Mazda CX-5 Signature Hitch Installation and Trim Removal
- Q&A: 2024 Mazda CX-5 Trailer Hitch and Wiring Recommendations with Mounting Brackets
- Q&A: Is Trimming Required to Install the etrailer Hitch # e98902 on My 2021 Mazda CX-5?
- Q&A: Recommended Hitch for a 2023 Mazda CX-5
- Article: Roof Rack Information
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit