T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• How to Access CHMSL Circuit on 2020 Ram 2500 Power Wagon
  The circuit you're looking to access is known as the CHMSL (center high mounted stop lamp). I've looked through the forums, and saw several folks mention that there should be a white wire with a purple stripe buried in the harness than runs along the passenger side frame rail. Barring that, the easiest place to access that circuit would be at the 3rd stop lamp atop the back of the cab. The # 118384 would access the brake lamp circuit for you, but the turn signal is also carried on that...
  view full answer...
• Adding a 4-Way Flat Connector For Tailgate Light Bar On a 2021 Ram 1500
  Yes the Tekonsha T-One Vehicle Wiring Harness # 118384 will plug and play into your factory tow package on your 2020 Ram 1500. This will allow you to plug into a Rampage SuperBrite LED Tailgate Light Bar # RA960134 on your Ram.
  view full answer...
• No Left or Right Trailer Stop/Turn Trailer Signals on a 2010 Chevy Silverado 2500
  If you have no trailer stop/turn signals, left or right on a 2010 Chevrolet Silverado 2500, you'll first want to start with taking a look in your owner's manuals for the correct fuse location. I went ahead and did this for you, the #1 fuse location is for the right trailer stop/turn and the #3 is for the left trailer stop/turn in the underhood fuse block. If the fuses are good the next step would be to inspect the terminals inside the trailer connector to be sure there is no corrosion....
  view full answer...
• Installing Pilot Automotive LED Fire Strip # 36049 on 2002 Chevy Silverado
  What you are describing is almost certainly a ground problem. If you are hardwiring the Pilot Fire Strip into place, you will need to make sure that BOTH ground wires are attached to clean bare metal on the truck frame or chassis (see photo). Leaving the 4-pole connector on the Fire Strip and installing a 4-pole connector on your truck like part # 118384 would would be your best bet, as there would be no cutting or splicing required.
  view full answer...
  
• 2004 GMC Sierra 1500 4x4 pickup truck 4 door short bed
  You'll need to begin by isolating the sources of the problem. Usually, the problem is in the trailer wiring. When the fuse lets loose, is the trailer plugged in? If so, you likely have a short circuit in the wiring on the trailer. Start at the trailer connector, and examine it for excessive corrosion or damage. Clean or repair as needed. Trace each circuit from the trailer plug back to its fixture. Look for wires that are pinched or for loose connections. Check for cracked or worn wire...
  view full answer...
• Will Plugging in a Rampage LED Light Bar Disable Backup Sensors on a 2009 Chevy Suburban
  It is likely that if you were to plug in the 4-Way, # 118384, and then plugged in the Rampage light, # RA960134, it would still shut off the back up sensors. This is because you are teeing into the factory harness so there would still be power draw through the factory wiring. To prevent that from happening you would need to hardwire in a 4-Way to the tail light wiring on your Suburban using # C59236. Since it pulls power from the vehicle battery and signals from the tail light wiring it...
  view full answer...
• Troubleshooting Loss of Power on Jack and Interior Trailer Lights with 2017 Ram
  It sounds like there is likely an issue with the 12V power circuit on your Ram's 7-Way connector, whether your jack and interior lights are powered directly from the 7-Way or via a battery on the trailer that is using the truck's 7-Way 12V power to maintain its charge. What you will want to do first is test the 12V pin on the truck's 7-Way with a circuit tester like # 40376 to see if you are getting power there. The 12V pin should be located at the 1 o'clock position on the 7-Way. If...
  view full answer...
• No Running Lights on Trailer When Using Tow Ready T-One Harness 118384 on 2004 Chevy Silverado
  Since you have replaced the factory 7-way connector on your 2004 Silverado due to corrosion you may also want to check the condition of the pins on the round vehicle connector under the rear bumper. This is the connector that mated to the original factory 7-way socket and that may now mate to the T-One Harness # 118384 if you are using this part. Since the outside contacts on the 7-way were corroded it is also possible that the other upstream connections may need cleaning as well. Even...
  view full answer...
  
• Availability of Wiring Harness for 2013 Volkswagen Tiguan
  There is one confirmed fit for a 4-pole trailer wiring harness for your vehicle and it is the custom harness # CU26FR by Curt. This T-connector plugs directly into existing wiring. It has a powered converter that reduces strain on the wiring system and is made using SMT to ensure superior performance. I have included a FAQ article to help with the wiring.
  view full answer...
• Compatability of the Replacement Multi-Tow 7-Way & 4 Pole Connector with 2008 Chevy Silverado
  Yes, the Replacement Multi-Tow 7-Way & 4 Pole Trailer Connector, item # 74682, will work as a replacement for your factory connector. This connector does not install in the original factory location without drilling (see video) and will have to be mounted near the hitch with the included mounting bracket if you do not want to drill mounting holes in the bumper. If you would like to retain the factory 7-way connector and just add a 4-way connector you could use the 4-Pole Trailer Adapter...
  view full answer...
• Hitch Recommendation For a 2010 Dodge Ram 2500 Mega Cab With a Factory Installed Hitch
  You might want to check the hitch on your 2010 Dodge Ram 2500, but it is usually welded on to the frame of your vehicle. It would be very difficult to remove. I would recommend the Curt Class V 2 Inch Hitch, part # C15409. This hitch has 17000 lbs towing weight capacity and 2550 lbs tongue weight capacity. If you will be towing with the Curt hitch you will also need the Draw-Tite Ball Mount, part # 40331, the part # PC3 Pin and Clip, and the hitch ball. Depending on the coupler size...
  view full answer...
• Where is the Connection Point For Trailer Wiring Harness # 118384 on a 2011 Jeep Liberty
  The Tow Ready Custom Fit Vehicle Wiring, # 118384, is designed to fit if your 2011 Jeep Liberty already has a factory 7-Way and you want to replace it with a 4-Way. The connection point is located behind the factory installed 7-way trailer connector, or up by the spare tire of the Jeep Liberty (GM Jeep Liberty only). I have included a link to the installation details for reference. If your Liberty did not come with a factory 7-Way trailer connector, you will need to use Draw-Tite Custom...
  view full answer...
• Does The Draw-Tite Class III Hitch # 75699 Fit Under The Bumper On A 2011 Jeep Grand Cherokee
  The Draw-Tite Class III 2 Inch Hitch, part # 75699, will install under the bumper on your 2011 Jeep Grand Cherokee. I am including a picture to the right that will show the proper position of the hitch on a Jeep Grand Cherokee. Also, I am including a link to the installation instructions for the Draw-Tite hitch. If you will be towing with this hitch you will want to check your owners manual or the Jeep dealer for the towing capacity of your 2010 Jeep Grand Cherokee. To complete your...
  view full answer...
  
• Troubleshooting Trailer Lights that Shut off When Vehicle Brakes are Applied
  Typically when trailer lights all cut out when a certain function is applied like the vehicle brakes the problem is either a bad ground for the trailer light assemblies or you are overdrawing the trailer light circuit. Most likely its the ground. First place to start would be to inspect the trailer wiring connector on your 2007 Chevy Silverado. Look for corrosion on the pins. Clean as necessary. Most trailer lights ground through the mounting assemblies. Since your trailer is brand new...
  view full answer...
• Replacing a Damaged 4-Way Trailer Connector on a 2000 Chevy Silverado 1500
  You can use the wiring harness that you referenced, # 18252, and wire it in directly to the tail lights to replace the 4-Way. The factory harness most likely leads up above the spare tire or along the driver side frame rail. If your truck did come with a factory trailer connector, you may be able to install # 118384 in its place which just plugs in to the factory harness if the truck came with a 7-Way originally. I have included a couple of video links that should help.
  view full answer...
• Locating 12V Trailer Battery Fuse on 2016 Ram 2500
  Based on my research there should be a pink 30 amp fuse located at the F30 position inside the power distribution center under the hood of your 2016 Ram 2500. This fuse is connected to the 12V power circuit on the factory 7-Way so you will want to make sure this fuse is present and in good condition. Please just let me know if you still don't get power at this pin after replacing the fuse and I will be happy to look into this further.
  view full answer...
• Will Tow Ready T-One Connector with 4-Pole Connector Fit 2008 Chevrolet Silverado
  The Tow Ready T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118384 is confirmed as a fit for the 2008 Chevrolet Silverado. This 4-Way trailer connector will plug into your Silverado's wiring behind the factory 7-Way connector at the rear of the vehicle. I've attached an installation video of this connector on a similar vehicle for you. I've also attached links to the wiring fitguide and the fitguide product categories for your 2008 Chevrolet Silverado for you.
  view full answer...
• How to Use a 4-Way and a 7-Way at the Same Time When the # HM40975 is Installed
  If you already have the # HM40975 installed on your vehicle you could install the part # 118384 as well and then you would have a second 4-way that would be accessible while the 7-way is being used. This 4-way will install inline with the 7-way harness and can be used at the same time as the 7-way.
  view full answer...
• Will Curt Bumper-Mount 2-Inch Trailer Hitch E-3S Fit Step Bumper on 2011 Toyota Tacoma
  According to my contact at Curt, their Bumper-Mount 2-Inch Trailer Hitch # E-3S will fit the step bumper on your 2011 Toyota Tacoma since this is a general-purpose universal-fit item. Installation hardware is included. The hitch mounting holes are spaced at 6-inches apart on center (the smaller set of holes) and on 8-3/4-inches apart on center (the larger set) as shown in the linked photo. If the spacing of the mounting holes does not match your bumper then you can drill new holes in the...
  view full answer...
  
• Can Rear Fascia Panel be Replaced After Installing Curt Trailer Hitch # 13424, 2011 Chevy Traverse
  You will notice in the instructions that I have linked for Curt Trailer Hitch, # 13424, that it states that the panel in question may be reinstalled on some models. So I spoke with my contact at Curt to determine if the 2011 Chevy Traverse was a model that it could be reinstalled on. He stated that they did not have information on the 2011 but on the 2010 it can be reinstalled. Basically, if the rear fascia is the same on the 2011, then it will fit. But if it has been redesigned, it will...
  view full answer...
• Troubleshooting Trailer Brake Controller Not Outputting Voltage
  Which brake controller are you using? How are you testing for brake output? Are you testing with the brake pedal pressed, or with the manual brake switch on the controller being actuated? If you have a proportional brake controller, you will NOT get output from the controller using the brake pedal UNLESS the vehicle is in motion. You SHOULD get power output with the manual brake switch actuated. A time-delayed controller should show power output both with the brake pedal being pressed...
  view full answer...
• Troubleshooting 2014 Ram 3500 Trailer Brake Controller Not Sending Power To Trailer Brakes Suddenly
  I would be happy to help! First things first using a circuit tester like # PTW2993 test the 5 o'clock pin on your 2014 Ram 3500's 7-way connector while a friend applies the manual override to the controller. If you are getting power, there then this means the issues is between your trailers 7-way connector and the brake magnets. You will want to check all of this wiring for any damage and replaced damaged sections with # 10-1-1 and heat shrink butt connectors # DW05745-5. If you do NOT...
  view full answer...
• Connecting 3rd Brake Light in Leer Cap to 2019 Ram 1500
  Actually, the correct part to wire in a truck bed cap's third brake light is the converter # PP20-702. Since your 2019 Ram's turn signals and brake lights run on one circuit this separates them so the light on the cap functions with just the brake lights. Each yellow wire connects to the truck's brake light/turn signal circuits, one on each side, and then the green wire goes to the third brake light. You can use the truck's trailer wiring to find the proper brake and turn signal circuits....
  view full answer...
• Towing and Kayak Carrier Setup for a 2018 Jeep Grand Cherokee Laredo
  I have everything you need to get your 2018 Jeep Grand Cherokee Laredo setup for towing and hauling your kayaks. For towing you are going to need a trailer hitch receiver, trailer wiring harness, ball mount, and hitch ball. I recommend using the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75699, the T-One Vehicle Wiring Harness part # 118727 without the factory tow package or part # 118384 with the factory tow package, and the Ball Mount Kit part # 989900. The trailer hitch has a...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?