Straight Tongue Trailer Coupler - 2 Inch Ball Coupler

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

...First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub...

...The channel of the Demco 21K # DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches...

...I am looking at the Demco couplers for a 3 inch channel that work with a 2 5/16 ball. There are two models rated for 21k lbs. one is DM16080-95 the other is DM15931-95. What is the difference...

The only difference between the Demco Channel Tongue Trailer Coupler part #12564 and Demco Channel Tongue Trailer Coupler part #DM12717 is the bolt pattern which is just slightly different with one having an extra hole.

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

...To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On # CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video...

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

...Hello I am about to finalize my selection but would like to know which one is better or more safety between the 2 models coupler DEMCO referenced above. I have noticed that one is more...

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

...I recommend etrailer.com Channel Tongue Coupler part # CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center...

...needed. The box shaft dimensions are 3inch x 4-5/8inch deep and is held in with a pin top and bottom through the frame. The ball is 2-5/16 I have attached a picture. I dont see anything on your site...

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

...First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub...

...The channel of the Demco 21K # DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches...

...I am looking at the Demco couplers for a 3 inch channel that work with a 2 5/16 ball. There are two models rated for 21k lbs. one is DM16080-95 the other is DM15931-95. What is the difference...

The only difference between the Demco Channel Tongue Trailer Coupler part #12564 and Demco Channel Tongue Trailer Coupler part #DM12717 is the bolt pattern which is just slightly different with one having an extra hole.

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

...To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On # CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video...

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

...Hello I am about to finalize my selection but would like to know which one is better or more safety between the 2 models coupler DEMCO referenced above. I have noticed that one is more...

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

...I recommend etrailer.com Channel Tongue Coupler part # CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center...

...needed. The box shaft dimensions are 3inch x 4-5/8inch deep and is held in with a pin top and bottom through the frame. The ball is 2-5/16 I have attached a picture. I dont see anything on your site...