Customers compare RM-048-8 to these similar products
Products Featured in this Video
Today we'll be reviewing RM-048-8, this is the Road Master High Low Hitch Adapter, traded at 10,000 pounds when it comes to weight capacity. It's going to have maximum ton weight of 400 pounds. This is designed to fit a two inch by two inch trailer hitch. The opening on the receiver itself is a two inch by two inch opening. If we take a measurement of the drop measuring from the top edge of the… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
A hitch mounted cargo carrier doesn't have a specified height requirement. You are correct that the longer the carrier extends the less ground clearance it will have on an inclined angle like a driveway. Some carriers have a rise integrated into…
view full answer...I do have an option for you but due to the way the vehicle is setup, all of the trailer hitches they make for it will hang down rather low. The other option I have for you to prevent it from scraping the pavement would be to use a skid wheel like the…
view full answer...We do not have the CAD drawings or blueprints for the Ultra-Fab Steel Roller, part #UF48-979020, but I have attached a photo of the roller with dimensions shown. The mounting bracket measures 1-1/4 inches from the center of the hitch pin hole to the…
view full answer...The towing capacity restrictions of the Curt ball mount part #D210 are pretty odd but basically if you were to use it with a bike rack like the XTC #S64670 you mentioned the capacity would not be reduced. I really like the Lippert Jack-It part…
view full answer...The collar on your trailer hitch cannot exceed 3-1/4" wide nor can the distance from the center of the hitch pin hole to the end of the receiver tube be more or less than 2-5/16 to 2-7/16" in order for the Roadmaster Rollaway Trailer Hitch…
view full answer...The Roadmaster Rollaway #RM-050 is designed for a hitch receiver that has a distance of 2-7/16 inches between the center of the hitch pinhole and the end of the face of the hitch receiver. At this distance, the support bar, which is at the bottom,…
view full answer...Looks like you bought the Titan Chain Multi-Arm Rubber Tire Chain Adjuster for Light Trucks #TCMA2 which is recommended for use with Titan tire chains that do not have tensioning devices and are between 14 and 24 inches in diameter.
view full answer...The difference between the #TCMA1 and #TCMA2 is the size and type of vehicle that they're designed for. The #TCMA1 is designed for passenger vehicles with wheels between 13"-20", where the #TCMA2 is designed for light trucks and SUVs…
view full answer...There isn't a plug and play option for a 7-way available, but we have the parts you'd need to complete the installation. You'll need to begin by installing a 4-pole trailer connector. There are two iterations of a 4-pole harness available…
view full answer...The legality of an obscured rear license plate varies from state to state. If you want to heed the letter of the law, the plate can be relocated to the rear of the cargo carrier. We sell quite a few cargo carriers, and to be honest, it is really not…
view full answer...You are correct that the weight of equipment loaded behind the tow vehicle's rear axle must be added to the tongue weight. The tongue weight is usually 10%-15% of the loaded trailer weight, plus the weight of this additional equipment. If we go…
view full answer...The most concealed trailer hitch receiver we have for your 2018 Honda Odyssey is the Draw-Tite Max-Frame Trailer Hitch Receiver part #76170. As you can see in the attached photo, only the receiver tube opening of the hitch is visible. This hitch has…
view full answer...